PŘÍSLUŠENSTVÍ K TELEFONU! KLIKNĚTE ZDE
 

Samsung Galaxy S5 MicroUSB Port Daughterboard Replacement

Send this link via e-mail


thumb image 1
thumb image 2
thumb image 3

Step 1 - Rear Case

  • Push a plastic opening tool or one of your fingernails into the opening to the left of the rear-facing camera.

  • Separate gently and twist the rear cover in order to get it off the back of the phone.

thumb image 1
thumb image 2
thumb image 3

Step 2 - Battery
Back to top

  • There is a recess in the bottom right corner of your phone's battery. Once again, push a plastic opening tool or your fingernail into the recess, and lift up the battery.

  • Take the battery out of the phone.

thumb image 1
thumb image 2

Step 3 - MicroSD Card
Back to top

  • Pull down the microSD card out of its slot with your fingertip.

  • Take the microSD card out of your phone.

Step 4 - SIM Card
Back to top

  • Take out the SIM card the same way you took out the microSD card in the previous step.

thumb image 1
thumb image 2
thumb image 3

Step 5 - Display Assembly
Back to top

  • Lift up the plastic midframe connector panel using a plastic opening tool.

  • Take out the connector panel with a pair of tweezers.

  • In case there isn't enough adhesive to put the panel back on your phone during the reassembling process, use a small amount of double-stick tape.

thumb image 1
thumb image 2

Step 6

  • Lift up the home button cable connector out of its socket with the sharp tip of a spudger.

thumb image 1
thumb image 2

Step 7

  • In the following steps, you will need to use an iOpener in order to warm the adhesive holding the display assembly to the rest of your phone. This way, you can remove the screen of your device more safely and easily. Remember to clean your microwave before putting the iOpener in it and make sure that the iOpener is clean, too. Heat the iOpener for one minute only, at the highest power setting. When it cools down, reheat it for a minute at a time. Be careful not to overheat the iOpener, and always wait at least two minutes before reheating it. When you pull out the iOpener, be sure to hold it by its tag or a corner.

  • Put the iOpener on the left side of the phone for at least 90 seconds.

  • Reheat the iOpener, and repeat the procedure for the right side of your phone.

thumb image 1
thumb image 2

Step 8

  • In the following steps, you will need to use an opening pick in order to remove the adhesive holding the front panel glass. Follow the instructions and pry only when you are told. If you encounter any resistance, reapply the iOpener and try again.

  • Push the edge of an opening pick under the bottom right side of the front glass.

thumb image 1
thumb image 2
thumb image 3

Step 9

  • Move the opening pick along the right side of the display.

thumb image 1
thumb image 2
thumb image 3

Step 10

  • Slide the pick around your phone's corner gently, and stop before the speaker grille, located at the top of the phone.

thumb image 1
thumb image 2
thumb image 3

Step 11

  • There is a narrow strip of adhesive above the earpiece speaker securing the top of the phone. Move the pick along the top of the speaker in order to avoid damaging internal components.

  • Slide the pick across the top of the phone. Be extremely careful not to push the pick in too deeply.

thumb image 1
thumb image 2
thumb image 3

Step 12

  • Slide the pick around the upper left corner carefully.

  • If you experience any resistance from the adhesive, reapply the iOpener to the left side of the phone, and try again.

thumb image 1
thumb image 2
thumb image 3

Step 13

  • Move the pick down the left half the phone. Stop once you get to the lower left corner.

thumb image 1
thumb image 2

Step 14

  • Make sure that the pick is securely placed and then slide it to the bottom left corner of the phone.

  • In the following step, you will need to place the iOpener over the home button end of your phone. You do not want your opening pick to slip out.

Step 15

  • Put the reheated iOpener over the bottom part of the display assembly.

  • This part of the phone holds delicate components, so make sure the adhesive is warm and easy to loosen. Otherwise, you can damage your phone.

thumb image 1
thumb image 2
thumb image 3

Step 16

  • The soft button and home button ribbon cables are located at the bottom end of your phone. Bear in mind that these cables can be easily damaged in case you push the pick in too far.

  • Move the end of the pick across the bottom edge of the display in order to remove the remaining adhesive.

thumb image 1
thumb image 2

Step 17

  • You will need to twist the pick to detach the glass from the phone.

  • In case you find it hard to remove the front panel, you might need to cut the adhesive a bit more.

thumb image 1
thumb image 2

Step 18

  • If you cannot detach the front panel with ease, you might need to separate the adhesive on the soft button cable.

  • Bear in mind that these cables are thin and can be easily damaged. This is why you need to make sure that you are only peeling them off the assembly, and not cutting them.

  • Push the pick under the soft button icons on the display and lift the button cables from the inside of the front panel.

thumb image 1
thumb image 2

Step 19

  • Lift, but do not remove, the home button part of display assembly.

  • Do not remove the front panel completely, because it is still attached to your phone by a connector.

  • If you plan on reusing the home button flex cable, make sure not to cut the cable from the home button. Adhesive can rip the cable and the home button apart. If this happens, your home button will still work, but the fingerprint scanner will not.

thumb image 1
thumb image 2
thumb image 3

Step 20

  • Life the front panel assembly cable connector out of its socket on the motherboard with the sharp tip of a spudger.

  • Take the front panel assembly off your phone.

Step 21 - Interior Midframe Assembly
Back to top

  • There are ten 3.4 mm Phillips screws on the display side of the midframe. You need to remove them.

Step 22

  • There are three screws on the battery side of the midframe. Flip your phone over and remove them.

  • Two 4.4 mm screws near the USB port

  • One 4.4 mm Phillips screw

thumb image 1
thumb image 2
thumb image 3

Step 23

  • Move the plastic opening tool along the left inner side of the interior frame. This way you'll separate the three white plastic clips.

thumb image 1
thumb image 2

Step 24

  • The midframe consists of two halves that sit around the motherboard.

  • Pull the long sides of the silver bezel gently away from the phone in order to separate the two halves of the midframe.

  • It might be easier to push in from the side of the battery compartment. However, be careful not to flex the interior half of the midframe, because the motherboard is mounted on it.

thumb image 1
thumb image 2

Step 25

  • Do the same thing on the right side of the bezel - pull the sides away from the interior section of the midframe.

thumb image 1
thumb image 2

Step 26

  • Lift any remaining corners out of the bezel with a plastic opening tool.

thumb image 1
thumb image 2

Step 27

  • Take the interior midframe/motherboard assembly carefully out of the white inner midframe.

thumb image 1
thumb image 2

Step 28 - Motherboard Assembly
Back to top

  • Push the tip of a spudger carefully under the antenna cable connector.

  • Lift the spudger gently upwards to remove the antenna connector from its socket on the motherboard.

thumb image 1
thumb image 2

Step 29

  • Do not remove the camera end of the motherboard from the midframe - only pull on it. This will give you access to the connectors in the back.

  • Do not remove the motherboard completely, seeing that it is still attached to the interior midframe via the microUSB port daughterboard connector.

thumb image 1
thumb image 2

Step 30

  • Lift up the daughterboard connector out of its socket on the motherboard using the flat end of a spudger.

thumb image 1
thumb image 2
thumb image 3

Step 31 - Motherboard
Back to top

  • Take out the front-facing camera connector out of its socket on the motherboard with the flat end of a spudger.

  • Take the front-facing camera off the motherboard.

thumb image 1
thumb image 2
thumb image 3

Step 32

  • Lift up the rear-facing camera connector out of its socket on the motherboard using the flat end of a spudger.

  • Take the rear-facing camera off the motherboard.

thumb image 1
thumb image 2

Step 33 - MicroUSB Port Daughterboard
Back to top

  • There are soft button ribbon cables attached to the microUSB port daughterboard. You need to separate them from the interior frame.

  • Peel the soft button cables off the interior frame using the flat end of a spudger.

Step 34

  • Turn over the midframe/motherboard assembly.

  • There is a 2.5 mm Phillips screw holding the microUSB port daughterboard to the midframe. You need to remove it.

thumb image 1
thumb image 2

Step 35

  • Insert the flat end of a spudger between the daughterboard cable and the interior midframe in order to remove the adhesive found there.

thumb image 1
thumb image 2
thumb image 3

Step 36

  • Rotate the midframe/motherboard assembly and then push in the spudger once again between the daughterboard and the interior midframe.

  • In order to remove the remaining adhesive, you need to twist the spudger.

  • Take the daughterboard off the interior midframe.




Tools:

Parts required for
this repair